BZCDJ - FOAMULAR EXTRUDED POLYSTYRENE
- MSDS: BZCDJ
- Manufacturer: UC INDUSTRIES A DIV OF OWENS CORNING
- Product Name: FOAMULAR EXTRUDED POLYSTYRENE
- National Stock Number: 6850-00F047003
Product Identification
Product ID:FOAMULAR EXTRUDED POLYSTYRENE
MSDS Date:05/01/1993
FSC:6850
NIIN:00F047003
MSDS Number: BZCDJ
Responsible Party
PARSIPPANY, NJ 07054-5000
US
Emergency Phone: 216-633-5848
Info Phone: 201-267-1605
Cage: UCCIN
Contractor
Telephone: 201-267-1605
Cage: UCCIN
Ingredients
POLYSTYRENE
CAS: 25038-60-2
Fraction By Weight: 87%
ETHANE, 1-CHLORO-1,1-DIFLUORO-, CHLORODIFLUOROETHANE (DOT),
CAS: 75-68-3
RTECS: KH7650000
Fraction By Weight: 12%
HEXABROMOCYCLODODECANE *96-1*
CAS: 3194-55-6
Fraction By Weight: 1%
DICHLORODIFLUOROMETHANE, FREON 12
CAS: 75-71-8
RTECS: PA8200000
Fraction By Weight: 12%
OSHA PEL 4950 MG/CUM
ACGIH TLV: 4950 MG/CUM
EPA Report Quantity: 5000 LBS
DOT Report Quantity: 5000 LBS
Hazards
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INHALATION: DUST MAY CAUSE RESPIRATORY
TRACT IRRITATION (UNDER NORMAL INDUSTRIAL USE THERE IS LITTLE/NO
DUST PRESENT).
Explanation of Carcinogenicity:NONE
Effects of Overexposure:DUST-TYPE MECHANICAL IRRITATIONS.
Medical Cond Aggravated by Exposure:DUST.
First Aid
First Aid:EYES: FLUSH W/WATER FOR 5 MINS; TREAT AS MECHANICAL EFFECT.
OBTAIN MEDICAL ATTENTION IN ALL CASES.
Fire Fighting
Flash Point Method:CC
Flash Point:>615F
Extinguishing Media:WATER, DRY CHEMICAL/CO2 EXTINGUISHER
Fire Fighting Procedures:WEAR SCBA IN CONFINED/POORLY VENTILATED AREAS.
Unusual Fire/Explosion Hazard:PRODUCES DENSE BLACK SMOKE WHILE BURNING.
THIS PRODUCT IS COMBUSTIBLE IF EXPOSED TO FIRE OF SUFFICIENT HEAT &
INTENSITY.
Accidental Release
Spill Release Procedures:HOUSEKEEPING CLEANUP. IF DUST PRESENT,
SWEEP/VACUUM & USE DUST RESPIRATOR PROTECTION. ALWAYS WEAR SAFETY
GLASSES/GOGGLES.
Handling
Handling and Storage Precautions:STORE MATERIALS OFF GROUND PROTECTED
FROM SUNLIGHT/BY A LIGHT COLORED OPAQUE POLYETHYLENE FILM/WAREHOUSE
ROOF & VENTILATED TO PREVENT EXCESSIVE TEMP.
Other Precautions:AVOID BREATHING DUST/FUMES THAT MIGHT BE GENERATED
DURING CUTTING/HEAT FABRICATION.
Exposure Controls
Respiratory Protection:NONE FOR BOARD, FILTER MASK FOR DUST.
Ventilation:LOCAL EXHAUST-NONE FOR BOARD, YES FOR DUST/FUMES.
Protective Gloves:NO
Eye Protection:SAFETY GLASSES DURING FABRICATION
Other Protective Equipment:NONE
Supplemental Safety and Health
Chemical Properties
Melt/Freeze Pt:M.P/F.P Text:220F
Decomp Temp:Decomp Text:>600F
Vapor Pres:0
Vapor Density:0
Spec Gravity:0.021-0.064
Evaporation Rate & Reference:(BU AC = 1): 0
Solubility in Water:NONE
Appearance and Odor:PINK, WHITE/GREEN, ODORLESS, CLOSED-CELL FOAM BOARD
Stability
Stability Indicator/Materials to Avoid:YES
HYDROCARBONS, ESTERS & AMINES.
Stability Condition to Avoid:OPEN FLAME IGNITION, HIGH TEMPS, SUNLIGHT.
Hazardous Decomposition Products:CO & CO2, TRACE AMOUNTS OF HYDROGEN
BROMIDE, HYDROGEN CHLORIDE, HYDROGEN FLUORIDE.
Conditions to Avoid Polymerization:HIGH TEMPS 165F, DIRECT SUNLIGHT.
Disposal
Waste Disposal Methods:RECLAIM/DISPOSE VIA AN APPROVED LANDFILL/BURN IN
AN APPROVED INCINERATOR W/EXCESS OXYGEN PER REGULATORY REQUIREMENS.
DISPOSE OF IAW/FEDERAL, STATE & LOCAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.